-
We often get asked about wire temperature ratings and how they relate to dimmer rack wiring and the allowable number of circuits in a conduit or wireway. While the ultimate authority on wire size, temperature ratings, and conduit fill is the project electrical engineer, and then the local inspector,...
-
*Menu structure is based on software v2.1.7 *If your rack does not have a configuration in it already, skip to step 6. Scroll to [Login] Enter the password 3,3,3,3 (scroll up to 3 and hit checkmark, etc.) Scroll to [Rack] and hit the checkmark Scroll to [Delete All Racks] and hit the checkmark It will...
-
Note: Basic/Portable mode is a simplified setup mode in CEM+ version 2.0 and above, intended for portable/touring racks. In basic/portable mode, the only active DMX is port A input. Once a unit is configured and running in basic/portable mode, anyone can press checkmark from the front panel to quickly...
-
CEM+ SMARTLINK POWER BOARD 2 7150B5620 LED Indicator Guide LED Color Component Location Purpose Default/Normal State Red CR1 Indicates a voltage imbalance on the LON network favoring NET B OFF (May glow slightly) Red CR2 Indicates a voltage imbalance on the LON network favoring NET A OFF (May glow slightly...
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
Question How much noise does a Sensor+ SineWave rack make? Answer ETC does not have a specific sound measurement for the complete rack, but the primary noise-generating component is the fan. The Manufacturer specifies the Sound Level for the fan operating at full speed as 65 dB.
-
Users with Internet Explorer 7 will not be able to connect to CEM+ (at least up through CEM+ version 2.1). Solution The difficulty is a component of the JavaScript code only recognizes internet explorer with major versions 5 and 6. When IE7 identifies itself with that number, the JavaScript code exits...
-
Most likely the rack has been configured for advanced feature dimmers and you are not using advanced feature dimmers. Call ETC Technical Service or refer to the article in this database regarding generating defaults for a Sensor rack.
-
Users with Internet Explorer 8 and above will not be able to connect to CEM+ versions before 3.0. Solution The difficulty is a component of the javascript code only recognizes internet explorer with major versions 5, & 6 (7 is also supported in version 2.2). When IE8 identifies itself with that number...