-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
If you have the hard drive replaced from an Obsession I with an early mother board, there is a chance you will get a “HDD Controller failure” message in the diagnostic screen. This happens from putting a new hard drive into an old computer that has problems keeping up. This is not something...
-
Manuals Obsession User Manual The Obsession (now generally known as Obsession 1 to differentiate it from Obsession 2 ) was a console produced by ETC from around 1992 to 1997, being obsoleted by the introduction of the Obsession 2. It was a natively tracking console with support for cue-only modes of...
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
Many ETC products provide timed event capabilities and may be affected by the 2007 adjustments to US Daylight Saving Time enacted with the Energy Policy Act of 2005. See the ETC Daylight Saving reference page for more information on what steps to take with your individual product
-
Question Which Kurta Digitizer Tablets Work with Obsession and Expression 2/3 Consoles? Answer Size Kurta Model # 12 x 12 XGT 90031 12 x 17 XGT 90033
-
ETCNet, now known as ETCNet1 to differentiate it from ETCNet2 and Net3, was ETC's original Ethernet based control protocol. It is a proprietary protocol and the specifications are not publicly available. ETCNet1 is a raw ethernet protocol, meaning that it will not work over a routed network and may...
-
Here are the valid MSC parameter ranges that we allow for both the Obsession and Expression lines. Neither console will respond to a 7F "all device" command format. Labels shown within angle brackets <> can be set. Values shown in hexadecimal must not be changed. Obsession Format: Obsession...
-
HISTORY AND THEORY OF CONSOLE OPERATION THEORY OF OPERATION OF LIGHTING CONSOLES There are two primary control philosophies used in the operation of entertainment lighting consoles, Pile-On, wherein the highest level instruction given to a channel is output to associated dimmers and Last Action, wherein...