-
Attached are the instructions for configuring an ETC supplied Dell Ethernet Switch for a typical ETCNet2 and Net3 installation. Note that switches generally ship configured from ETC, these instructions are for reference in case a switch needs to be reset. 3771.4000M2202_revA.pdf
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
Network Configuration Editor (NCE) Knowledge Base: ETC Network IP Addresses Help Your Technician Help you
-
Question Do you need to ground the node? Answer Yes. This helps displace any static electricity that may be acquire.
-
Digitizers, such as the Kurta tablet do not work reliably through ETC Net2 Nodes.
-
The Net2 node power supply can be either a 12V or a 24V unit. The Node itself can accept voltage from 12V to 30V.
-
Question What is the optimum operating temperature for a 2 port node? Answer 0 degrees to 50 degrees Celcuis 32 degrees to 106 degrees Fahrenheit (This limit is determined by the LCD screen needs.)
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
Upgrading two ports from 1.0.0 The procedure for upgrading from v1.0.0 to v1.1.0 is detailed in the ETCNet2 Two Port v1.1.0 Release Note and must be completed before you upgrade to any other later version. Version 1.1.0 software is functionally identical to v1.0.0, but contains a different bootloader...