-
Default IP Ranges For ETC Products Below are the ETC Network addressing standards. Bold numbers or modes are the default for devices that ship with a preconfigured IP. These standard ranges should be used unless a different range is required by the site. ETC Product IP Range Congo 10.101.80.101 to 10...
Posted to
ETC Product Wiki
by
Tracy.Fitch
on
06-18-2013
Filed under: CEM+, CEM3, Congo, Congo Kid, CongoJr, DMX, Element, Emphasis, Eos, Ethernet, Gateway Configuration Editor, GCE, Ion, iphone, ipod, iRFR, IRFU, KnowledgeBase, Legacy Unison, Light Server, Mosaic, NCE, Net2, Net3, Network, Obsession, ObsessionII, Paradigm, Pharos, Sensor+, Show Control, Unison, WRFU
-
Net3 One Port DMX Gateway Gateway Configuration Editor (GCE) ETCNet2 Network Configuration Editor (NCE) DMX Ethernet Knowledge Base: 1-Port Gateways Drop Out ETC Network IP Addresses One Port Gateways Cannot Communicate with NCE Updating 1-Port Gateways to work in GCE Problems with Strand SN110 node...
-
ETCNet2 Network Configuration Editor (NCE) does not ship installed on an Eos Family console, but can be installed at any time. NCE is a useful tool used to configure Net2 DMX nodes, Net2 Video nodes, Net3 Gateways running in Net2 mode, and Net3 1 port gateways. To install NCE on an Eos Family console...
-
Two Port Wallmount Node Two Port Touring Node The ETCNet2 Two Port Node was available as either a wallmount (backbox mounting) version or as a touring version with either two male or two female 5 pin XLR connectors. Similarly to other Net2 products the connectors can be inputs or outputs irrespective...
-
The ETCNet2 DMX Node provides a way to either input or output DMX from a Net2 Network system. The node can also be used in a Net1 system similar to an RIU. There were several variants produced : Connectors could be either front or rear mounted DMX connectors were available as 4 male, 4 female or a mixture...
-
Unexpected NCE Crashes If you are running NCE 4.0 and you are not connected to a node or the node is not in V4, NCE will crash and close when performing basic functions. Some of them are: Get unbound nodes, discover nodes, and get configuration from nodes. While you will probably not do this when you...
-
Network Configuration Editor (NCE) ETC's Network Configuration Editor (NCE) is a spreadsheet-style software program designed to make configuring ETCNet2 TM DMX and Video nodes easy. With NCE, you can configure the paramaters of any port on any ETCNet2 node in a NET2 system. Through an Ethernet connection...
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
Net 3 Four & Two Port DMX/RDM Gateway Product Page Gateway Configuration Editor (GCE) ETCNet2 Network Configuration Editor (NCE) DMX RDM Ethernet Knowledge Base: ETC Network IP Addresses RDM Discovery Interval Timing in Net3 Gateways Maximum Number of RDM Devices on a Net3 Gateway Maximum Number...
-
The ETCNet2 Video Node provided a way to extract video information from the network and display it on one or two VGA monitors. A typical use would be a way to monitor the state of the console from the stage managers desk or production table. The node took a 12V DC power supply input; it's outputs...