-
The Net3 Radio Focus Remote (RFR) base station has a single bi-color LED that indicates different states: Solid Green = powered and running Slow Irregular Blink Red/Green = wired or wireless data activity Rapid Regular Blink Red/Green = identify function (probably triggered by GCE - should timeout after...
-
Attached are the instructions for configuring an ETC supplied Dell Ethernet Switch for a typical ETCNet2 and Net3 installation. Note that switches generally ship configured from ETC, these instructions are for reference in case a switch needs to be reset. 3771.4000M2202_revA.pdf
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
The maximum number of RDM enabled opto-splitters that may be daisy chained together is 4. Since RDM splitters have to shorten the time between some of the packets, chaining more opto-splitters will result in unsatisfactory performance. It's also important to remember that legacy DMX opto-isolators...
-
The maximum number of RDM devices that can be attached to a single RDM enabled port on a Net3 Gateway is 32. This matches the DMX standard for the maximum number of devices on a DMX line. However, adding an RDM opto-isolator does not increase this number.
-
The ‘RDM Discovery Interval’ property of a Net3 Gateway defaults, in the first RDM version (v2.0.0) of the Net3 Two and Four Port Gateways, to 1000ms. Previous gateway software defaulted this property to 100ms. New gateways will be manufactured with a default of 1000ms. Existing gateways...
-
There are a couple of specialized steps for setting up the Net3 RFR on Congo as opposed to Eos/Ion. On the handheld unit, find an available frequency and set the channel as described in the RFR setup guide. With the base station plugged into the Congo go into [System Settings] from the Heartbeat screen...