-
Eos, Ion, Element, and Eos/Ion RPUs support external touchscreens, as do Congo, Congo jr, and Congo Lightserver running version 5+ software. Net3 RVIs support as well (again with Congo 5+ as a restriction). There are two options for acquiring touchscreens: ETC stocks a touchscreen (part # M231) available...
-
If you are having trouble connecting an Eos/Ion/Element client pc running Windows Vista to the master console (and you can ping the console), make sure the Service Location Protocol is 'Started' and 'Automatic'. To do this: Right-click on the 'My Computer' icon on the desktop...
-
Manuals Operations Manual 1.7 Eos Eos Remote Processor Unit Net3 Radio Focus Remote (RFR) Gateway Configuration Editor (GCE) Touchscreen Monitors Related Links: Why Did My Console Do That? Knowledge Base: Eos/Ion/Element client and Windows Vista Updating Eos / Ion Software Importing Lightwright data...
-
Manuals Net3 Radio Focus Remote Setup Guide Net3 RFR Gateway Configuration Editor (GCE) Knowledge Base: Net3 Radio Focus Remote (RFR) Setup On Congo Net3 RFR Base Station LED States ETC Network IP Addresses Help Your Technician Help you
-
Console Settings Eos, Ion and Element output both Net2 (EDMX) and Net3 (sACN/E1.31) levels via ethernet. As these protocols are enabled by default, you will likely not need to enable them in the Settings menu of the Eos/Ion/Element welcome screen. Open the Settings menu, then navigate to the Network...
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
Attached is a spreadsheet that will allow you to map out your DMX to EMDX addresses based on universe number. 3632.EDMX_Translation_Charts.xls
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-24-2009
Filed under: CEM+, Congo, CongoJr, Element, Emphasis, Eos, Ion, KnowledgeBase, Legacy Unison, ObsessionII, Sensor+, Unison
-
There has been an on-going issue with using the above listed Planar brand of monitors with ION/EOS/Element. In a nutshell, the Planar monitors will spontaneously go into a mode they call “safe mode” (dark screen and amber power LED). Once the monitor is in safe mode the monitor will not successfully...