-
DMX512 is the most commonly used data protocol for theatrical control. For a more technical overview of DMX see the Wikipedia article on DMX. DMX is an international ANSI standard maintained by ESTA. It is not proprietary to any one manufacturer. An enhancement to DMX512 called RDM is also available...
-
The below cards were offered for a time by ETC Ltd (UK). The attached .PDF contains some base level info on these cards. Please note: There is no user manual available. .PDF 5381.Black Secrets of the Relay Cards.pdf 4722.Relay Controller features.doc 3348.Relay Rack Features.doc Relay Driver Card Analog...
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
Question Do you need to ground the node? Answer Yes. This helps displace any static electricity that may be acquire.
-
The Net2 node power supply can be either a 12V or a 24V unit. The Node itself can accept voltage from 12V to 30V.
-
Question What is the optimum operating temperature for a 2 port node? Answer 0 degrees to 50 degrees Celcuis 32 degrees to 106 degrees Fahrenheit (This limit is determined by the LCD screen needs.)
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
Net 3 Four & Two Port DMX/RDM Gateway Product Page Gateway Configuration Editor (GCE) ETCNet2 Network Configuration Editor (NCE) DMX RDM Ethernet Knowledge Base: ETC Network IP Addresses RDM Discovery Interval Timing in Net3 Gateways Maximum Number of RDM Devices on a Net3 Gateway Maximum Number...
-
The maximum number of RDM enabled opto-splitters that may be daisy chained together is 4. Since RDM splitters have to shorten the time between some of the packets, chaining more opto-splitters will result in unsatisfactory performance. It's also important to remember that legacy DMX opto-isolators...