-
Eos, Ion, Element, and Eos/Ion RPUs support external touchscreens, as do Congo, Congo jr, and Congo Lightserver running version 5+ software. Net3 RVIs support as well (again with Congo 5+ as a restriction). There are two options for acquiring touchscreens: ETC stocks a touchscreen (part # M231) available...
-
Manuals Net3 Radio Focus Remote Setup Guide Net3 RFR Gateway Configuration Editor (GCE) Knowledge Base: Net3 Radio Focus Remote (RFR) Setup On Congo Net3 RFR Base Station LED States ETC Network IP Addresses Help Your Technician Help you
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
Manuals Congo Jr. User Manual Congo Congo Light Server Net3 Radio Focus Remote (RFR) Congo Radio Remote Focus Unit (cRRFU) Gateway Configuration Editor (GCE) Touchscreen Monitors Knowledge Base: External Touch Screens for Eos , Ion , Congo , Congo jr Using X-Keys with Congo/Congo jr/Congo Light Server...
-
Manuals Congo User Manual Congo Congo Light Server Net3 Radio Focus Remote (RFR) Congo Radio Remote Focus Unit (cRRFU) Gateway Configuration Editor (GCE) Touchscreen Monitors Knowledge Base: External Touch Screens for Eos , Ion , Congo , Congo jr Net3 Radio Focus Remote (RFR) Setup On Congo Congo Client...
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
Attached is a spreadsheet that will allow you to map out your DMX to EMDX addresses based on universe number. 3632.EDMX_Translation_Charts.xls
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-24-2009
Filed under: CEM+, Congo, CongoJr, Element, Emphasis, Eos, Ion, KnowledgeBase, Legacy Unison, ObsessionII, Sensor+, Unison
-
There are a couple of specialized steps for setting up the Net3 RFR on Congo as opposed to Eos/Ion. On the handheld unit, find an available frequency and set the channel as described in the RFR setup guide. With the base station plugged into the Congo go into [System Settings] from the Heartbeat screen...
-
Some modern USB Memory Sticks come with a software technology called U3 pre-installed. U3 allows a flash drive to act as a container for applications by running special, proprietary Windows software when attached to a Windows PC. However, this software will not run on ETC products which accept USB memory...