-
I. Network Configuration The iRFR requires that your console be on a wireless network. Below are a couple examples of how you may choose to configure your wireless network: *NOTE: Your lighting network should never have a direct connection to the internet. It is also critical that the wireless component...
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
Manuals Wireless Romote Focus Unit (WRFU) v1.1 User Manual ETCNet2 Wireless Remote Focus Unit (WRFU) Knowledge Base: WRFU IPAQ 5500 Setup Instructions WRFU IPAQ 5500 Will Not Connect to the Access Point ETC Network IP Addresses Help Your Technician Help you
-
Manuals Emphasis User Manual Emphasis ETCNet2 Wireless Remote Focus Unit (WRFU) Express/Expression/Emphasis Radio Remote Focus Unit (RRFU) Express/Expression/Emphasis Remote Focus Unit (RFU) Knowledge Base: Emphasis 1.8 Key Cap Replacement Kit Emphasis Displays Only the Emphasis and Data Mode Emphasis...
-
Manuals Obsession II User Manual Obsession II Facepanel Obsession II DPS Obsession II SPS The Obsession II (Obsession 2) console was the successor to the Obsession 1, and was similar from a programming point of view. Obsession2 is a natively tracking console. Obsession II systems are natively networked;...
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
Question How to setup WRFU IPAQ 5550 Answer Attached to this article is a merge of the ETC WRFU software installation instructions and IPAQ wifi setup instructions. Use this to speed installation and setup. 0412.WRFU_Installation_Procedure.pdf
-
I. Connecting to Your Console NOTE: If you have not already setup your console's wireless network and configured your iPhone/iPod to use that network, you need to start here: iRFR: How to Setup Your Wireless Network 1. On your console, you will need to enable iRFR support (which if off by default...
-
I. Connecting to Your Console NOTE: If you have not already setup your console's wireless network and configured your iPhone/iPod to use that network, you need to start here: iRFR: How to Setup Your Wireless Network On your Congo or CongoJr you will need to have Remote Controls enabled. No other...
-
RFR with Congo/CongoJr Also see: Getting Started with Congo/CongoJr The iRFR has the same functionality as the Net3 RFR. The RFR works within its own field and this field can be cleared from the console. All channel intensity levels generated by the remote can only be recorded into targets from the remote...