-
Sensor CEM version 2 code does not have an "always on" firing mode but we can set a dimmer that way. To set a dimmer to be always on: Press [Setup] Press [1] for Dimmer Type the dimmer number on the numeric keypad and press [Enter] Press [4] to select Switched firing mode and press [Enter]...
-
Manuals Sensor CEM v3.1 User Manual CEM Classic The CEM classic was the control module supplied with Sensor dimming racks until the release of CEM+ in 2004. There were several versions produced for different voltage ranges. It is important to check the model of your unit when ordering spares Model Voltage...
-
If your relays are chattering or not firing in your Sensor, Sensor+ or Unison rack there may be a problem with the neutral wire on your signal distro card. Make sure that the neutral wire is present and connected on both ends. This problem can also cause ELV10 modules to not work correctly in test mode...
-
Manuals Sensor 230V Dimmer Module Datasheet Sensor Dimmer Modules Knowledge Base: What is the Curve on a CE (European) Sensor Module Breaker? Sensor Dimmer Module BTU Dissipation Non-dim vs Switched mode/Regulated vs. Unregulated Module Information Summary ELV10 And Test Mode In Sensor+ Why Are My Relays...
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
Manuals Sensor+ CEM+ v3.0.0 User/Configuration Manual Sensor+ CE Installation Manual CEM+ Related Links: Dimmer Doubling Knowledge Base: High Altitude Effects on Sensor and Unison Dimmers Saving CEM+ Processor Configuration Files to a PC Minimum Levels in CEM+ How do I match Intersities and dimmer curves...
-
Manuals Sensor Touring Rack User Manual Sensor Portable Pack User Manual Sensor+ CEM+ Touring Rack Retrofit Manual Sensor Touring Racks/Packs Knowledge Base: Sensor Patchbay Upgrade High Altitude Effects on Sensor and Unison Dimmers Sensor Touring Rack CEM Classic Data Backplane Pinout Sensor Touring...
-
Quick Summary: If you've got devices with electronics inside being powered from a dimmer in a sensor rack, set the firing mode to switched . If you're on a Unison rack, a SmartPack, a SmartBar, or a SmartModule, set the mode to non-dim What those options mean: Non-dim dimmers output regulated...
-
In Sensor Touring Racks, ETC no longer uses the J2 connector for data input into the CEM. This is now accomplished through the J3 connector which is the smaller one in the middle of the CEM backplane. This connector is smaller and much less prone to damage from pulling CEM's in and out and jarring...
-
Module Information Summary This summary provides module information broken down by market and application. Four major market groups are used to separate modules: UL market – ETC Americas, 120v-60hz power, Sensor and Unison products CE market – ETC Europe, 230v-50hz power, Sensor CE and Unison...