-
Manuals Response Network Controller User Manual The Response Network Controller (RNC) was a combined protocol converter, DMX patch unit and HTP merger. It featured two input and two output ports supporting DMX, D192, K96 or AMX192 data protocols. Allows softpatching of 1024 dimmers from two multi-protocol...
-
Manuals Response Merger User Manual Response Merger The Response Merger combines two incoming DMX512 signals into a single DMX512 output signal. This allows two consoles to control the same lights with highest level taking priority. DMX DATA PINOUT 1 COMMON 2 DATA - 3 DATA + Data Loss Behavior Hold time...
-
Problem: Can't do Custom Patch on a Response Merger Answer: To enable the custom patch for a Response Merger, J8-position 5 needs to be removed from the standard jumper config. This leaves position 8 the only one jumpered.
-
RESPONSE 96 OUT DMX/D192/K96 DATA PINOUT 1 COMMON 2 DATA - 3 DATA + AMX DATA PINOUT 1 COMMON 2 CLOCK + 3 CLOCK - 4 ANALOG ANALOG OUTPUT PINOUT 1-32 CHANNELS (1-32) 35-36 COMMON ADDRESSING Starting Output numbers can be calculated as shown: [(1st Output# + 5)/6] = Wheel Setting i.e. [(13+5)/6]= 03 Outputs...
-
Problem: The DMX input on port 1 of the RNC works fine, but the input on port 2 is not outputting correctly. Answer: First step: make certain within the Setup menu on the RNC that you have the two input ports merging into one output. See the manual for this information. If the correct settings are in...
-
RESPONSE CONVERTER DMX DATA PINOUT 1 COMMON 2 DATA - 3 DATA + AMX DATA PINOUT 1 COMMON 2 CLOCK + 3 ANALOG 4 CLOCK - DIP SWITCHES DMX to AMX SW1 UP, SW3 DN, SW4 UP AMX to DMX SW1 DN, SW3 UP, SW4 UP SELF TESTS 910 CHASE* 920 FADE ALL* 930 FADE CHASE* 940 SELECTED OUTPUT TO FULL 950 ALL TO PERCENT 960 ALL...
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
RESPONSE 32 OUT/A32 OUT DMX DATA PINOUT 1 COMMON 2 DATA - 3 DATA + AMX DATA PINOUT 1 COMMON 2 CLOCK + 3 CLOCK - 4 ANALOG ANALOG OUTPUT PINOUT 1-32 CHANNELS (1-32) 35-36 COMMON DATA TYPE SELECTION DMX SW1 UP, SW3 DN AMX SW1 DN, SW3 UP FILTERS NONE SW5 DN, SW6 DN SMALL SW5 DN, SW6 UP MEDIUM SW5 UP, SW6...
-
RESPONSE MERGER DMX DATA PINOUT 1 COMMON 2 DATA - 3 DATA + Data Loss Behavior Hold time is 3 min 45 Sec with a 3 min 45 Sec fade JUMPERS CUSTOM PATCH--REMOVE JUMPER FROM J8, POSITION 5 MERGER LEDS A NOT USED B NOT USED C FLASH OUTPUT DATA ERROR D FLASH OUTPUT DATA OK E ON PORT 2 DATA ERROR F ON PORT...
-
RESPONSE 96 IN DMX/D192 DATA PINOUT 1 COMMON 2 DATA - 3 DATA + ANALOG INPUT PINOUT 1-32 CHANNELS (1-32) 35-36 COMMON JUMPERS J4 DMX/D192 J3 POSITIVE/NEGATIVE VOLTAGE TRIM POTS P2 FULL ADJUST P1 ZERO ADJUST SLAVING - RELOCATE J5 AND J6 - REMOVE Z4 ON SLAVE UNITS