-
Manuals Net3 Radio Focus Remote Setup Guide Net3 RFR The Net3 RFR provides a wireless remote control for consoles supporting ETCNet3, which includes Congo, Eos, Ion and Element. It features a network base station that can be recieve data and power over PoE or directly connected to the the console via...
-
Default IP configuration by product Product IP Address Subnet Mask Gateway IP Unison 10.101.10.101 255.255.0.0 10.101.10.101 Obsession Primary RPU 10.101.30.101 255.255.0.0 10.101.30.101 DMX Node 10.101.0.99 255.255.0.0 0.101.0.99 Default subnet mask and gateway Item Value Subnet Mask 255.255.0.0 Default...
Posted to
ETC Product Wiki
by
Tracy.Fitch
on
05-12-2010
Filed under: CEM+, Congo, CongoJr, DMX, Element, Emphasis, Eos, GCE, Ion, KnowledgeBase, Legacy Unison, Net2, Net3, Obsession, ObsessionII, Sensor+, Unison, WRFU
-
1-PORT GATEWAY ISSUE There have been reports of issues with 1-Port Net3 Gateways running firmware version 4.0.0 (distributed with NCE 4.3.0) running in Net2 mode with Eos/Ion consoles running software versions 1.8.1, 1.8.2, and 1.9.0. After using the console for a period of time without changing any...
-
Net3 One Port DMX Gateway ETCNet2 Network Configuration Editor (NCE) DMX Ethernet Knowledge Base: 1-Port Gateways Drop Out ETC Network IP Addresses One Port Gateways Cannot Communicate with NCE Problems with Strand SN110 node receiving DMX Help Your Technician Help you
-
Some Net3 one port gateways running firmware version 4.0.0.9.0.10 shipped incorrectly configured for a default ETCNet2/3 system. They have proper ETC firmware installed but have an IP address of 10.4.xxx.xxx. Our normal ETCNet2/3 IP range is 10.101.xxx.xxx with a subnet of 255.255.0.0, so the improperly...
-
ETC recommends using rechargeable batteries. As with any rechargeable battery, we have found that these provide the best source of power and longest operating life when allowed to be fully discharged and then fully charged. Most users simply use the RFR and then plug it back into the recharger when done...
-
The Net3 Radio Focus Remote (RFR) base station has a single bi-color LED that indicates different states: Solid Green = powered and running Slow Irregular Blink Red/Green = wired or wireless data activity Rapid Regular Blink Red/Green = identify function (probably triggered by GCE - should timeout after...
-
Attached are the instructions for configuring an ETC supplied Dell Ethernet Switch for a typical ETCNet2 and Net3 installation. Note that switches generally ship configured from ETC, these instructions are for reference in case a switch needs to be reset. 3771.4000M2202_revA.pdf
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML