-
Net3 One Port DMX Gateway Gateway Configuration Editor (GCE) ETCNet2 Network Configuration Editor (NCE) DMX Ethernet Knowledge Base: 1-Port Gateways Drop Out ETC Network IP Addresses One Port Gateways Cannot Communicate with NCE Updating 1-Port Gateways to work in GCE Problems with Strand SN110 node...
-
Default IP Ranges For ETC Products Below are the ETC Network addressing standards. Bold numbers or modes are the default for devices that ship with a preconfigured IP. These standard ranges should be used unless a different range is required by the site. ETC Product IP Range Congo 10.101.80.101 to 10...
Posted to
ETC Product Wiki
by
Tracy.Fitch
on
02-29-2012
Filed under: CEM+, CEM3, Congo, Congo Kid, CongoJr, DMX, Element, Emphasis, Eos, Ethernet, Gateway Configuration Editor, GCE, Ion, iphone, ipod, iRFR, IRFU, KnowledgeBase, Legacy Unison, Light Server, Mosaic, NCE, Net2, Net3, Network, Obsession, ObsessionII, Paradigm, Pharos, Sensor+, Show Control, Unison, WRFU
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML
-
Net 3 Four & Two Port DMX/RDM Gateway Product Page Gateway Configuration Editor (GCE) ETCNet2 Network Configuration Editor (NCE) DMX RDM Ethernet Knowledge Base: ETC Network IP Addresses RDM Discovery Interval Timing in Net3 Gateways Maximum Number of RDM Devices on a Net3 Gateway Maximum Number...
-
The maximum number of RDM enabled opto-splitters that may be daisy chained together is 4. Since RDM splitters have to shorten the time between some of the packets, chaining more opto-splitters will result in unsatisfactory performance. It's also important to remember that legacy DMX opto-isolators...
-
The maximum number of RDM devices that can be attached to a single RDM enabled port on a Net3 Gateway is 32. This matches the DMX standard for the maximum number of devices on a DMX line. However, adding an RDM opto-isolator does not increase this number.