-
Many ETC products provide timed event capabilities and may be affected by the 2007 adjustments to US Daylight Saving Time enacted with the Energy Policy Act of 2005. See the ETC Daylight Saving reference page for more information on what steps to take with your individual product
-
How much power does an Express 24/48 use? 0.15A Peak 0.03A Normal/Idle
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
From our testing, Strand SN110 nodes seem to require a 6 millisecond idle time after the last stop bit. In order for ETC consoles and DMX nodes and gateways to send DMX to them you must set their DMX Output speed to "slow". A deep clear or reset will change this to "fast", so the...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
07-27-2009
Filed under: Congo, CongoJr, DMX, Element, Emphasis, Eos, Express, Expression, Ion, KnowledgeBase, Net2, Net3, Obsession, ObsessionII, SmartFade, SmartFadeML
-
There are 2 types of Express power supplies, 5-pin and 8-pin power supplies. The following lists the pin-outs for each power supply. A diagram of each pin-out is also included. 8-pin power supplies +5v pins 1, 2, and 3 +12v pin 4 GND pins, 5, 6, 7, and 8 5-pin power supplies +5v pin 3 +12v pin 5 GND...
-
Running Express Software Version 2.0 Express 125 125 Express 250 250 Express 24/48 48 Express 48/96 96 Express 72/144 144 Running Express Software Version 3.01 and greater: Express 125 125 Express 250 250 Express 24/48 96 Express 48/96 192 Express 72/144 240
-
CHANNEL NUMBERS/STANDARD PATCH: Gray Unselected channel White Channel is not selected by Only Function Yellow Selected channel. Controlled by the "Y" wheel CHANNEL NUMBERS/FIXTURE PATCH: Gray bar Surrounds all channels of one fixture Light gray Low channels for 16-bit data types Gold Channels...
-
Question Which Kurta Digitizer Tablets Work with Obsession and Expression 2/3 Consoles? Answer Size Kurta Model # 12 x 12 XGT 90031 12 x 17 XGT 90033
-
Question If a Net2 node is being used in Net1 mode are the ports assignable, as they would be in Net1 mode? Answer In Net1 mode, the ports of the node emulate the DMX ports on the console. For example, a 4 port node when connected to an Express console would output two separate universes of DMX via Port...
-
ETCNet, now known as ETCNet1 to differentiate it from ETCNet2 and Net3, was ETC's original Ethernet based control protocol. It is a proprietary protocol and the specifications are not publicly available. ETCNet1 is a raw ethernet protocol, meaning that it will not work over a routed network and may...