-
Default IP Ranges For ETC Products Below are the ETC Network addressing standards. Bold numbers or modes are the default for devices that ship with a preconfigured IP. These standard ranges should be used unless a different range is required by the site. ETC Product IP Range Congo 10.101.80.101 to 10...
Posted to
ETC Product Wiki
by
Tracy.Fitch
on
06-18-2013
Filed under: CEM+, CEM3, Congo, Congo Kid, CongoJr, DMX, Element, Emphasis, Eos, Ethernet, Gateway Configuration Editor, GCE, Ion, iphone, ipod, iRFR, IRFU, KnowledgeBase, Legacy Unison, Light Server, Mosaic, NCE, Net2, Net3, Network, Obsession, ObsessionII, Paradigm, Pharos, Sensor+, Show Control, Unison, WRFU
-
Users with Internet Explorer 7 will not be able to connect to CEM+ (at least up through CEM+ version 2.1). Solution The difficulty is a component of the JavaScript code only recognizes internet explorer with major versions 5 and 6. When IE7 identifies itself with that number, the JavaScript code exits...
-
Users with Internet Explorer 8 and above will not be able to connect to CEM+ versions before 3.0. Solution The difficulty is a component of the javascript code only recognizes internet explorer with major versions 5, & 6 (7 is also supported in version 2.2). When IE8 identifies itself with that number...
-
*Menu structure is based on software v2.1.7 with a CEM+ that begins running in Full-Featured mode *If your rack does not have a configuration in it already, skip to step 6. Note: Basic/Portable mode is a simplified setup mode in CEM+ version 2.0 and above, intended for portable/touring racks. In basic...
-
Verify that the Max Scale setting for each dimmer on the CEM+ is set to about 118. Verify that the Curve setting for each dimmer on the CEM+ is set to Mod Square. If this doesn’t work, try Sensor 2.0. Make sure to check the voltage readings with a True-RMS meter. NOTE: Any work (including metering...
-
*Menu structure is based on software v2.1.7 *If your rack does not have a configuration in it already, skip to step 6. Scroll to [Login] Enter the password 3,3,3,3 (scroll up to 3 and hit checkmark, etc.) Scroll to [Rack] and hit the checkmark Scroll to [Delete All Racks] and hit the checkmark It will...
-
Note: Basic/Portable mode is a simplified setup mode in CEM+ version 2.0 and above, intended for portable/touring racks. In basic/portable mode, the only active DMX is port A input. Once a unit is configured and running in basic/portable mode, anyone can press checkmark from the front panel to quickly...
-
CEM+ SMARTLINK POWER BOARD 2 7150B5620 LED Indicator Guide LED Color Component Location Purpose Default/Normal State Red CR1 Indicates a voltage imbalance on the LON network favoring NET B OFF (May glow slightly) Red CR2 Indicates a voltage imbalance on the LON network favoring NET A OFF (May glow slightly...
-
When equipment goes bad out in the field, it's often extremely helpful if the owner/end user can keep track of the circumstances of the failure. This is especially true when the problem is intermittent and might not occur when the technician is present. Service Technicians are exceptionally skillful...
Posted to
ETC Product Wiki
by
Kelsey Aleckson
on
08-24-2009
Filed under: AAS, Acclaim, arri, ASTS, AVAB, CEM, CEM+, Congo, CongoJr, cRRFU, DAS, Dimmer, Distribution, DMX, ECMUX, Element, ELTS, Emphasis, Eos, ETCLink, Ethernet, Express, Expression, GCE, Idea, Ion, Irideon, K96, KnowledgeBase, Legacy Unison, LMI, Lon, MDD, MDR, MicroII, MicroVision, MIDI, MPE, NCE, Net2, Net3, Obsession, ObsessionII, Pharos, RDM, Response, RFR, RFU, RRFU, RS-232, RVI, Sensor, Sensor+, SineWave, SmartBar, SmartFade, SmartFadeML, SmartModule, SMPTE, Source Four, Source4, Touchscreen, Unison, Vision, WRFU
-
Most likely the rack has been configured for advanced feature dimmers and you are not using advanced feature dimmers. Call ETC Technical Service or refer to the article in this database regarding generating defaults for a Sensor rack.