Electronic Theatre Controls
Welcome to ETC's Online Community
All Tags » unison (RSS)

Browse Site by Tags

Showing related tags and posts across the entire site.
  • Legacy Unison LCD Background images

    Is it possible to download the LCD background images from a Legacy CEMi without a "PC Interface Station"? Save config to disk on the processor only saves the config (does what it say's on the tin!) Light manager seems only tobe able to upload images via network, not download. Many Thanks...
    Posted to Unison Dimming and Control by marcusbirkin on 09-10-2012
    Filed under: unison, legacy, Unison Light Manager, CEMi, background
  • Push buttons and master control

    Hi, Ive been asked to set up a 5 button 1 fader station so that the buttons will pull up a recorded preset. The level of the lights is to be determined by the location of the fader. The intention is to drop a set of preset/group of lights to zero, select a new preset/group and fade them in. So far all...
    Posted to Unison Dimming and Control by Steve_aitch on 07-27-2012
    Filed under: Light Designer, Paradigm, unison
  • anolog adress system channel control

    we use a anolog adress system which in turn is sitting on a gaint red box.(we use this system for overhead stage lighting) at one point a couple of lights stopped working to the 8 channel pots. i went through the patch menu, and i discovered that work light was enabled for some of them. i turned this...
    Posted to Unison Dimming and Control by poland fun on 10-13-2011
    Filed under: unison
  • dimmer errors

    New to forum so I hope I am in correct one. Our church has a 12 dimmer rack in the chapel. The lcd on the sensor controller has a blinking message 'dimmer error'. All light appear to be working normally ie dim and turn on with programmed buttons. I noticed that the last dimmer doesn't have...
    Posted to Unison Dimming and Control by stgjim on 04-07-2011
    Filed under: unison
  • Dimmers do not shut off in switched mode.

    Problem: Dimmers set to switched mode will not shut off. Answer: Sensor 3.1 had a software bug that held dimmers in switched mode to 15 percent. This was fixed in 3.11 software. Workaround: Set non-motorized loads to non-dim. Sites using motors on d20's should think about using R20s regardless of...
    Posted to ETC Product Wiki by Kelsey Aleckson on 07-22-2010
    Filed under: Dimmer, Sensor, Unison
  • Neutral current based on dimming control percentages

    Please find an attached Excel file that can calculate and graphically display phase and neutral current based on dimming control percentages. Place your control levels in the upper left corner and the graphs and calculator (on the upper right) will be updated. In the example we played with, A was at...
    Posted to ETC Product Wiki by Kelsey Aleckson on 07-22-2010
    Filed under: Dimmer, Unison
  • What is the best ETC dimmer to use to control a Fan or Motor?

    Question: What is the Best ETC dimmer to use to control a Fan or Motor? Answer: SCR-based dimmers are the best to use in this situation based on the fact that it may receive a non-linear kick-back in voltage. For this reason the D15 and D20 modules are your best choice. This kick-back may damage the...
    Posted to ETC Product Wiki by Kelsey Aleckson on 07-22-2010
    Filed under: Dimmer, Sensor, Unison
  • How Does Unison Serial Access Protocol (USAP) Work?

    Reference the USAP Programming Guide (ETC P/N 7080M1011). There is also a test utility (USAPTest), which allows you to test and troubleshoot USAP commands.
    Posted to ETC Product Wiki by Kelsey Aleckson on 07-19-2010
    Filed under: Unison
Page 5 of 15 (300 items) « First ... < Previous 3 4 5 6 7 Next > ... Last »
Powered by Community Server (Commercial Edition), by Telligent Systems