Browse Site by Tags - Electronic Theatre Controls

KnowledgeBase: ETC Network IP Addresses

Default IP Ranges For ETC Products Below are the ETC Network addressing standards. Bold numbers or modes are the default for devices that ship with a preconfigured IP. These standard ranges should be used unless a different range is required by the site. ETC Product IP Range Congo 10.101.80.101 to 10...

Posted to ETC Product Wiki by Tracy.Fitch on 06-18-2013
Filed under: CEM+, CEM3, Congo, Congo Kid, CongoJr, DMX, Element, Emphasis, Eos, Ethernet, Gateway Configuration Editor, GCE, Ion, iphone, ipod, iRFR, IRFU, KnowledgeBase, Legacy Unison, Light Server, Mosaic, NCE, Net2, Net3, Network, Obsession, ObsessionII, Paradigm, Pharos, Sensor+, Show Control, Unison, WRFU

EOS LeaveQueried

This might belong in the EOS forum, but it's about networking so.... By what mechanism does the following occur: "QuartzFram LeaveQueried ldr=0F72CA82-7AC9-3E1E-BA7B-2E762E294DF0(42) mbr= EE4EE15F-CF03-47FF-9402-D4638A5B0099(80000000) ssn=2" It's the EOS console log, and pertains to...

Posted to Networking Discussions by marcusbirkin on 10-05-2012
Filed under: EOS, Sensor+, ACN, Quartz

KnowledgeBase: ELV Modules And Test Mode In Sensor+/3 & DRd

CEM+/CEM3 The ELV module circuit must be powered (with the breaker on) before getting a control signal in order for the module to output. Why? The processor in the ELV module needs to see a zero on the pwm line before it is ready to output. With CEM+/3, test mode supplies a constant +5V signal starting...

Posted to ETC Product Wiki by Tracy.Fitch on 07-12-2012
Filed under: CEM+, CEM3, Dimmer, DRd, ELV10, Sensor Rack, Sensor+, Sensor3

Sensor+ Connect with Internet Explorer 9

Users with Internet Explorer 9 and above will not be able to connect to CEM+ versions before 3.0. Solution The difficulty is a component of the javascript code only recognizes internet explorer with major versions 5, & 6 (7 is also supported in version 2.2). When IE9 identifies itself with that number...

Posted to ETC Product Wiki by Tracy.Fitch on 04-03-2012
Filed under: CEM+, Sensor+

KnowledgeBase: Sensor+ Connect with Internet Explorer 7

Users with Internet Explorer 7 will not be able to connect to CEM+ (at least up through CEM+ version 2.1). Solution The difficulty is a component of the JavaScript code only recognizes internet explorer with major versions 5 and 6. When IE7 identifies itself with that number, the JavaScript code exits...

Posted to ETC Product Wiki by Tracy.Fitch on 04-03-2012
Filed under: CEM+, KnowledgeBase, Sensor+

Sinewave dimmer racks and relay modules

We have a SineWave rack that provides power to dimmers in our lobby. It is the only source of power in a number of places, and it would be useful to have it provide clean power so that we could plug in sensitive electronics like projectors, computers, moving lights and electronic ballast equipment to...

Posted to Sensor and Matrix Dimming systems by angeleads on 02-23-2012
Filed under: sensor+, sinewave

Re: Network slows down after enabling ACN with CEM+ modules

I had re-imaged the ION to v 1.9.6, so everything is running the latest versions. The last I could figure out before my show wrapped was that with StreamingACN and Sensor Rack Feedback enabled in the Ion's Networking setup, it just slowed the network down too much for either the RFR or iRFR (iPod...

Posted to Networking Discussions by Jaylaca on 05-20-2011
Filed under: Network, ion, CEM+, Sensor+, ACN

Network slows down after enabling ACN with CEM+ modules

Hi, I've got a small setup that is working great consisting of: ION console v1.9.1.9.0.30 Linksys SD208 10/100 switch Netgear Netgear WPN802 v2 WAP RFR connected via Net3 USB iRFR on iPod Touch v 1.1.42 (through WAP) This setup works great. All are connected via a Linksys SD208 10/100 switch. Both...

Posted to Networking Discussions by Jaylaca on 03-16-2011
Filed under: sACN Networking, USB, Net 3, Wireless, Network, iRFR, ion, CEM+, Sensor+, configuration, 10/100, rfr