Browse Site by Tags - Electronic Theatre Controls

KnowledgeBase: ETC Network IP Addresses

Default IP Ranges For ETC Products Below are the ETC Network addressing standards. Bold numbers or modes are the default for devices that ship with a preconfigured IP. These standard ranges should be used unless a different range is required by the site. ETC Product IP Range Congo 10.101.80.101 to 10...

Posted to ETC Product Wiki by Tracy.Fitch on 06-18-2013
Filed under: CEM+, CEM3, Congo, Congo Kid, CongoJr, DMX, Element, Emphasis, Eos, Ethernet, Gateway Configuration Editor, GCE, Ion, iphone, ipod, iRFR, IRFU, KnowledgeBase, Legacy Unison, Light Server, Mosaic, NCE, Net2, Net3, Network, Obsession, ObsessionII, Paradigm, Pharos, Sensor+, Show Control, Unison, WRFU

aRFR: How to Setup Your Wireless Network

Network Configuration The aRFR requires that your console be on a wireless network. DMX Only System You can use either a Wireless Access Point (WAP) or a Wireless Router. Some consoles will require the use of a crossover cable if going to a WAP. On your console, it is recommended that you have {Address...

Posted to ETC Product Wiki by Richard on 04-23-2013
Filed under: Android, aRFR, Network, remote control, wireless

aRFR: Getting Started with Your Eos Family Console

Connecting to Your Eos Family Console NOTE: If you have not already set up your console's wireless network and configured your Android device to use that network, please see aRFR: How to Setup Your Wireless Network . Once your Android device is configured to be on the same wireless network as your...

Posted to ETC Product Wiki by Anders Ekvall on 08-25-2011
Filed under: Android, aRFR, Element, Eos, Ion, Network, wireless

Re: ION and ETCNet2?!

More info would help. How is your ETCnet setup? Are you using net2 nodes? My theater is all ETCnet with net2 nodes and my scrollers work fine. One thing I have noticed is that if I plug the ethernet cable into the board after I have turned the board on, I have to exit the Ion or reboot to get it to talk...

Posted to The Eos Family Forum (Eos Ti, Eos, Gio, Ion) by bosox242 on 04-17-2009
Filed under: network, ION

Re: iRFR

Internet access is different than having access to the router or switch via TCP/IP. Just because you have to use a browser to set settings on your router doesn't mean that it has to have internet access. You would set up a closed network for your space. It could only consist of the console and the...

Posted to The Eos Family Forum (Eos Ti, Eos, Gio, Ion) by Jeff Mabray on 04-16-2009
Filed under: network, Wireless connectivity, RFR

Using Eos Offline software as a "listen only" client.

Hello once more, Long story short, I am looking to provide an LD with a selected/active channels display so that he can easily view what is going on without having to lean over my shoulder when he says " can I see what Ch20 is at?" or suchlike. To avoid using my own screen space, one solution...

Posted to The Eos Family Forum (Eos Ti, Eos, Gio, Ion) by LeoW on 02-11-2009
Filed under: network, Offline Editor

What can you do with ETCNet with an Express board? (Help!)

I'm primarily looking to see if there was any way that I could write shows on the lighting console and then be able to retrive them in a .shw file on a computer hooked up to the network. What I am trying to do is make the risky buisness of handling shows on 3-1/2in. A: Floppy disks obsolete. If anybody...

Posted to Express/Expression/Emphasis and Obsession by shadowkid92 on 11-30-2008
Filed under: Express, ETCNet, help, network