Browse Site by Tags - Electronic Theatre Controls

Net3 One Port DMX Gateway

Net3 One Port DMX Gateway Gateway Configuration Editor (GCE) ETCNet2 Network Configuration Editor (NCE) DMX Ethernet Knowledge Base: 1-Port Gateways Drop Out ETC Network IP Addresses One Port Gateways Cannot Communicate with NCE Updating 1-Port Gateways to work in GCE Problems with Strand SN110 node...

Posted to ETC Product Wiki by starksk on 07-30-2012
Filed under: DMX, Ethernet, NCE, Net3

grab Artnet with EOS

Hello I work only this month with a Vector, there is an ASCII Export function but it doesn't work properly : sometimes values are wrong and the cues contains only change values... If I can grab artnet with Eos, or Congo to make an ASCII show file I will be safe for the next theater. thanks Pilou

Posted to The Eos Family Forum (Eos Ti, Eos, Gio, Ion) by pilou on 06-30-2012
Filed under: nce

Installing NCE on an Eos Family Console

ETCNet2 Network Configuration Editor (NCE) does not ship installed on an Eos Family console, but can be installed at any time. NCE is a useful tool used to configure Net2 DMX nodes, Net2 Video nodes, Net3 Gateways running in Net2 mode, and Net3 1 port gateways. To install NCE on an Eos Family console...

Posted to ETC Product Wiki by Hans.Hinrichsen on 05-17-2012
Filed under: Element, Eos, Ion, NCE, Net2

KnowledgeBase: ETC Network IP Addresses

Default IP Ranges For ETC Products Below are the ETC Network addressing standards. Bold numbers or modes are the default for devices that ship with a preconfigured IP. These standard ranges should be used unless a different range is required by the site. ETC Product IP Range Congo 10.101.80.101 to 10...

Posted to ETC Product Wiki by Tracy.Fitch on 02-29-2012
Filed under: CEM+, CEM3, Congo, Congo Kid, CongoJr, DMX, Element, Emphasis, Eos, Ethernet, Gateway Configuration Editor, GCE, Ion, iphone, ipod, iRFR, IRFU, KnowledgeBase, Legacy Unison, Light Server, Mosaic, NCE, Net2, Net3, Network, Obsession, ObsessionII, Paradigm, Pharos, Sensor+, Show Control, Unison, WRFU

ETCNet2 Two Port DMX Node

Two Port Wallmount Node Two Port Touring Node The ETCNet2 Two Port Node was available as either a wallmount (backbox mounting) version or as a touring version with either two male or two female 5 pin XLR connectors. Similarly to other Net2 products the connectors can be inputs or outputs irrespective...

Posted to ETC Product Wiki by Tracy.Fitch on 09-16-2010
Filed under: DMX, Ethernet, NCE, Net2

Studio Color 575 Lamp off & GCE question

I have two questions open to anyone: 1) I am currently running 10 HES Studio Color 575's on my ION and the Lamp Off command isn't working. The fixture reset command will and the lights function as normal, but all Lamp Off does is open and then close the dimmer shutter. Is there a specific command...

Posted to The Eos Family Forum (Eos Ti, Eos, Gio, Ion) by jhdesynz on 11-25-2009
Filed under: ION, GCE, lamp off, studio color, net2, nce, net3

NCE, GCE and Net3 Services onto Congo.

sclausen: I believe if you install NCE or GCE on your console, you will get buttons in the Settings (the system settings available from the startup screen) to launch those programs. Also, Net3 Services may be installed on consoles running v5.0.x software to provide DHCP and time server functions from...

Posted to The Congo Family Forum (Congo, Congo jr, Congo Kid and Light Server) by Richard on 09-26-2008
Filed under: Networking, NCE, Net3

Re: Networking

Hello, For Congos and CongoJr the recomended IP ranges are 10.101.80.101 to 10.101.80.253 and 10.101.81.101 to 10.101.81.253. So you could make your Congo be 10.101.80.101 and the Jr 10.101.80.102. The NCE and GCE buttons in Congo Settings in v 5.0.1 are for access to NCE (Network Configuration Editor...

Posted to The Congo Family Forum (Congo, Congo jr, Congo Kid and Light Server) by okrogell on 09-10-2008
Filed under: Networking, NCE, GCE