Browse Site by Tags - Electronic Theatre Controls

Net3 One Port DMX Gateway

Net3 One Port DMX Gateway ETCNet2 Network Configuration Editor (NCE) DMX Ethernet Knowledge Base: ETC Network IP Addresses One Port Gateways Cannot Communicate with NCE Problems with Strand SN110 node receiving DMX Help Your Technician Help you

Posted to ETC Product Wiki by Tracy.Fitch on 03-05-2010
Filed under: DMX, Ethernet, NCE, Net3

DMX Relay Card

.PDF Black Secrets of the Relay Cards Relay Controller Features Relay Rack Features These cards were offered for a time by ETC Ltd (UK). The attached Acrobat .pdf files contain some basic info on these cards. Note: There is no user manual available. Relay Driver Card Analog Output Card 6 Relay Add-On...

Posted to ETC Product Wiki by Tracy.Fitch on 02-04-2010
Filed under: DMX

DMX Speed

DMX has a number of timing variables. The information presented here will probably be useful for only a small proportion of users, but can assist in getting troublesome DMX equipment to work. If you need further information, the book "Recommended Practice for DMX512 - A guide for installers and...

Posted to ETC Product Wiki by Tracy.Fitch on 02-04-2010
Filed under: DMX

DMX

DMX512 is the most commonly used data protocol for theatrical control. For a more technical overview of DMX see the Wikipedia article on DMX. DMX is an international ANSI standard maintained by ESTA . It is not proprietary to any one manufacturer. An enhancement to DMX512 called RDM is also available...

Posted to ETC Product Wiki by Tracy.Fitch on 12-15-2009
Filed under: DMX

Re: Expression DMX In

Thank you for clarifying Sarah. Do I have DMX In correctrly in that it uses one console to cue another? And that the slave console shows up as basicly a preset to the master? I'm still not clear on how that works. But I do understand the two espressions merged portion of the lesson. so many channels...

Posted to Express/Expression/Emphasis and Obsession by meatpopsicle on 03-13-2009
Filed under: expression, DMX, Emphasis, dmx in, d'oh

Any ideas for this?

So. We have one sensor rack (has ethernet plug on front, DMX cable /input isn't accessable at all) We have a ETC Express 24/48 connected to it (has universe 2 still free along with free ethernet plugin) the board is in the booth... far away from the rack fyi). For a upcoming show we would like to...

Posted to Networking Discussions by John on 03-10-2009
Filed under: net3, brand, computer, DMX, gel changers, USB, ethernet, etc, ideas, express, moving gobo

Re: DMX on CAT5....to shield or not to shield?

Unless something major has changed since I moved to Germany 4 years ago….When using CAT5 for DMX the cable must be in metal conduit from point to point. I too have seen installations where it was not and times where there was conduit at the back-box but it dispersed once it reached above the drop...

Posted to Service Technician Forum by mmeskill on 03-03-2009
Filed under: DMX

Express DMX IN / OUT

Can I simply use the DMX IN / OUT with two consoles and a single data line to control a large plot with a singular cue list? I have used MIDI to connect a Hog 2 (movers) and Obsession (dimmers) but each had a cues list sometimes with dummy cues. There was also a programmer for each desk. I don't...

Posted to Express/Expression/Emphasis and Obsession by SBC on 01-24-2009
Filed under: express 48-96, DMX, express 24/48

Dr. DMX surrenders

I captured the real Dr. DMX today. Doug Fleenor finally succumbed to my chase of him. He surrendered peacefully , hands raised to show he had no digital weaponry. As I apprehended the suspect - Ken Wagner forced me to see demos of all the latest Fleenor design products. The were showing an addition to...

Posted to What am I thinking? What are you thinking? by dlincecum on 10-22-2006
Filed under: DMX, Fleenor Design