Electronic Theatre Controls
Welcome to ETC's Online Community
All Tags » cem+ (RSS)

Browse Site by Tags

Showing related tags and posts across the entire site.

  • KnowledgeBase: ETC Network IP Addresses

    Default IP Ranges For ETC Products Below are the ETC Network addressing standards. Bold numbers or modes are the default for devices that ship with a preconfigured IP. These standard ranges should be used unless a different range is required by the site. ETC Product IP Range Congo 10.101.80.101 to 10...
    Posted to ETC Product Wiki by Tracy.Fitch on 06-18-2013
    Filed under: CEM+, CEM3, Congo, Congo Kid, CongoJr, DMX, Element, Emphasis, Eos, Ethernet, Gateway Configuration Editor, GCE, Ion, iphone, ipod, iRFR, IRFU, KnowledgeBase, Legacy Unison, Light Server, Mosaic, NCE, Net2, Net3, Network, Obsession, ObsessionII, Paradigm, Pharos, Sensor+, Show Control, Unison, WRFU

  • KnowledgeBase: ELV Modules And Test Mode In Sensor+/3 & DRd

    CEM+/CEM3 The ELV module circuit must be powered (with the breaker on) before getting a control signal in order for the module to output. Why? The processor in the ELV module needs to see a zero on the pwm line before it is ready to output. With CEM+/3, test mode supplies a constant +5V signal starting...
    Posted to ETC Product Wiki by Tracy.Fitch on 07-12-2012
    Filed under: CEM+, CEM3, Dimmer, DRd, ELV10, Sensor Rack, Sensor+, Sensor3

  • Sensor+ Connect with Internet Explorer 9

    Users with Internet Explorer 9 and above will not be able to connect to CEM+ versions before 3.0. Solution The difficulty is a component of the javascript code only recognizes internet explorer with major versions 5, & 6 (7 is also supported in version 2.2). When IE9 identifies itself with that number...
    Posted to ETC Product Wiki by Tracy.Fitch on 04-03-2012
    Filed under: CEM+, Sensor+

  • KnowledgeBase: Sensor+ Connect with Internet Explorer 7

    Users with Internet Explorer 7 will not be able to connect to CEM+ (at least up through CEM+ version 2.1). Solution The difficulty is a component of the JavaScript code only recognizes internet explorer with major versions 5 and 6. When IE7 identifies itself with that number, the JavaScript code exits...
    Posted to ETC Product Wiki by Tracy.Fitch on 04-03-2012
    Filed under: CEM+, KnowledgeBase, Sensor+

  • Channels showing errors

    We run and Eos, RPU, Sensor system and our normal configuration is RPU as Master/Primary and Eos as backup with device descovery enabled for Sensor feedback, etc. The Eos was accidentally switched to Client mode recently and every channel patched to a Sensor dimmer was showing an error on the screen...
    Posted to The Eos Family Forum (Eos Ti, Eos, Gio, Ion) by hacronymus on 02-17-2011
    Filed under: EOS, RPU, EOS 1.9.6, CEM+, Sensor

  • factory default???

    On a Sensor ECM + (softw 2.2.0)... Can we do a factory default setting to reset dimmer param.??? How? Secret combinations of holding some buttons on front panel? If we want to restore a rack faster than changing a lot of setting manually... can we do something to reset easily toward a realy basic mode...
    Posted to Sensor and Matrix Dimming systems by CAS on 10-09-2010
    Filed under: Sensor, CEM, CEM+, Rack, DMX

  • Upgrade CEM 2 to CEM 3

    Hi, I have been getting some anomalies when setting up dimmer doubling, stuff like EDMX/No Control and other inconsistent behavior, though they generally work fine. I would like to upgrade the firmware to CEM v3. Any icky things that might arise or red flags? Do the system configurations get whacked...
    Posted to Sensor and Matrix Dimming systems by eugp on 10-04-2010
    Filed under: CEM+

  • Adjusting contrast settings on CEM+

    So in a system I am building for a rental client, I have one CEM+ where the display contrast is much lower than normal. At first when I power it up, it is fine through the "ETC CEM+" screen and for a few seconds on the "ETC CEM+ 3.1.0" screen, before it goes dim. Once it goes dim...
    Posted to Sensor and Matrix Dimming systems by BLGranucci on 08-30-2010
    Filed under: CEM+

  • Sensor TS - Our best idea to date

    Today I have guest post by Bryan Palmer- a project manager at ETC. He emailed me a great study of our dimming past and dimming future. See his bright idea here . David
    Posted to What am I thinking? What are you thinking? by dlincecum on 11-01-2006
    Filed under: CEM+, Sensor
Page 1 of 7 (140 items) 1 2 3 4 5 Next > ... Last »
Powered by Community Server (Commercial Edition), by Telligent Systems