Electronic Theatre Controls
Welcome to ETC's Online Community
All Tags » ion (RSS)

Browse Forum Posts by Tags

Showing related tags and posts for the ETC Dimming and networking systems group. See all tags in the site
  • Re: Congo iRFR dropping connection...802.11g router just too old?

    I was having repeated and constant disconnects with my iRFR and my ION after 30 seconds or so, called ETC, and was given a strange, but very useful tip. Disable 3G on your iPhone. Now it stays connected all the time, every time. Of course, I get within 10 feet of a Clear-Com system now and I make horrible...
    Posted to Networking Discussions (Forum) by nfarwell on 04-28-2010
    Filed under: Wireless, iRFR, 3g, ion, iphone
  • Net3 2 Port Node

    Hi All, I apologize if this has been covered before, I searched the topics first and didnt find anything... I have a fresh out of the box Net3 2 port node to go along with our new Ion console. I've gone into the Network Settings on the Ion Shell to configure the node, but I'm not having any luck...
    Posted to Networking Discussions (Forum) by MattGorka on 09-28-2010
    Filed under: Net 3, Network, ion
  • Network slows down after enabling ACN with CEM+ modules

    Hi, I've got a small setup that is working great consisting of: ION console v1.9.1.9.0.30 Linksys SD208 10/100 switch Netgear Netgear WPN802 v2 WAP RFR connected via Net3 USB iRFR on iPod Touch v 1.1.42 (through WAP) This setup works great. All are connected via a Linksys SD208 10/100 switch. Both...
    Posted to Networking Discussions (Forum) by Jaylaca on 03-16-2011
    Filed under: sACN Networking, USB, Net 3, Wireless, Network, iRFR, ion, CEM+, Sensor+, configuration, 10/100, rfr
  • Re: Network slows down after enabling ACN with CEM+ modules

    I had re-imaged the ION to v 1.9.6, so everything is running the latest versions. The last I could figure out before my show wrapped was that with StreamingACN and Sensor Rack Feedback enabled in the Ion's Networking setup, it just slowed the network down too much for either the RFR or iRFR (iPod...
    Posted to Networking Discussions (Forum) by Jaylaca on 05-20-2011
    Filed under: Network, ion, CEM+, Sensor+, ACN
  • configuring Net2 gateway

    I am sure that this has already been discussed some where, but here I go. What is the process for configuring the Net3 Gateways for multiple universes of DMX. I am in a brand new studio and need to set up the Nodes for my DMX in the studio. By the way the studio has an Ion. I am not seeing any real process...
    Posted to Networking Discussions (Forum) by Tvlights 1 on 09-20-2011
    Filed under: net3, DMX, ion, Node, Gateway
  • Ion to Net3 Communication Issue

    In trying to set up my Ion again after receiving it from the shop, I'm unable to get it to fully communicate with my 2-port Net3 Gateway. As far as I can tell, I have all IP addresses assigned correctly: GCE recognizes the node, and I can even remotely flash the LCD screen as well as ping the node's...
    Posted to Networking Discussions (Forum) by MattWebb on 01-25-2012
    Filed under: net3, DMX, ethernet, Net 3, Network, ion, Node, Gateway
  • Re: Congo iRFR dropping connection...802.11g router just too old?

    I discovered a solution based on a user having similar troubles with a Congo console. This procedure pertains to iOS 5.x devices. On your iPod/iPhone, navigate to Settings>General>Reset and select and confirm 'Reset Network Settings'. Your device will then reboot itself. After the reboot...
    Posted to Networking Discussions (Forum) by Braden on 02-28-2012
    Filed under: EOS, iRFR, ion, Element
  • 4 Port gateway looks online?

    I just ran-into this issue last night(almost literally right into the 4 port gateway while batten was down). I've got a work around I'll describe later, yet has anyone discovered the issue causing? Being I can't recreate the issue I'm unable to prevent it in future. This past saturday...
    Posted to Networking Discussions (Forum) by jhamil on 03-29-2012
    Filed under: sACN Networking, DMX, ethernet, Net 3, ion, configuration, Gateway
  • Re: Network slows down after enabling ACN with CEM+ modules

    As of the end of my last show I was really only able to trace it back to the the fact that the Ion is not powerful enough (cpu-wise) to handle that much network traffic. I did not get a chance to try upgrading the switches from 10/100 to 1000 based switches. This is a "network bogging down"...
    Posted to Networking Discussions (Forum) by Jaylaca on 05-05-2012
    Filed under: Network, iRFR, ion, rfr
  • ION connection to Net3 2port gateway

    I have an ION console now connected to a Net3 2 port gateway. I need settings information to attach a router to add wireless remote focus capability to the system. I plan to use is Linksys WRT54GVS 2.4G wireless router. Need some guidance for the Linksys IP network settings.Thanks
    Posted to Networking Discussions (Forum) by rmarston on 08-18-2012
    Filed under: Net 3, ion, iRFR Net3
Page 1 of 2 (12 items) 1 2 Next >
Powered by Community Server (Commercial Edition), by Telligent Systems