Electronic Theatre Controls
Welcome to ETC's Online Community
All Tags » LED (RSS)

Browse Forum Posts by Tags

Showing related tags and posts for the Control Consoles group. See all tags in the site
  • Re: Video

    Ab der Version 6.0 gibt es parallel zu POS/FW zwei neue Listenanzeigen "LED" (für LED-Fixtures) und "MEDIA" (für Mediaserver), dazu entsprechende Bedienungen wie 'x S LED' bzw. 'x S MEDIA', sowie Erweiterungen für Libra. Die Release 6.0 wird spätestens...
    Posted to NT/NTX Products (Forum) by hleiter on 03-02-2009
    Filed under: Video, Mediaserver, LED
  • Elation Design LED (DLED) 12 Brick template and usage

    I am trying to setup and use a DLED 12 LED fixture (this has 4 of each LED color: red, green, and blue) on our Congo jr console. It works fine in 6ch mode (using 6ch template) with all the red LEDs together, green LEDs together, and blue LEDs together using the color dials to adjust them, and 3 other...
    Posted to The Congo Forum (and Congo jr, too!) (Forum) by Pacman on 02-25-2009
    Filed under: Congo Jr., LED, Templates, Parameters
  • Effekte

    Hallo, wird es in Zukunft weitere Effekte für den Chaser geben? Es gibt ja nur zwei Arten von Chaser, abwechselnt oder aufbauend. Ist ein bißchen zu wenig. Es musste doch möglich sein einen Chaser auszuwählen, als Flicker oder Zufall u.s.w. . Wird die Effekt Tast bald belegt?? Was...
    Posted to The Congo Forum (and Congo jr, too!) (Forum) by Scholle on 09-28-2007
    Filed under: Congo, Congo Jr., LED, chase
  • Re: RGB Chase

    Hi all sorted, For a reason the chase wasnt acting on Rate, you need tochange in and out time to what you need so as I needed a step chase change these to 0.1 then use the tap button to get you tempo. If the in / out is set to nothing the chase carnt finish so it loops, Hope Ive explained myself ok as...
    Posted to The Congo Forum (and Congo jr, too!) (Forum) by cknapper on 05-12-2007
    Filed under: LED, Times, chase
  • RGB Chase

    Hi all OK I have a RGB chase made up of 8 point cues, Ive transfered these to master and my chase work fine on these, the problem is when i put my pessets in a seq and make them into a chase, The chase starts but each step adds to each one instead of swapping form step to step, Ive tried X.M,L but its...
    Posted to The Congo Forum (and Congo jr, too!) (Forum) by cknapper on 05-11-2007
    Filed under: LED
  • Re: pixeline 1044

    Hi Mike, The template does not necesarily need to have an Intensity parameter for Fade with Intensity to work. Fade with Intensity will work two ways. 1. With an Intensity parameter in the template. 2. Without an Intensity parameter in the template. But then you have to have the channel your RGB device...
    Posted to The Congo Forum (and Congo jr, too!) (Forum) by okrogell on 03-14-2007
    Filed under: LED, Fade with Intensity
  • Re: pixeline 1044

    Hi to you to is it me or is it just me having problems / questions on the congo or is everyone else an expert this desk !!!!!!! :P OK After long night on my offline congo I believe that I now have all my pixelines patch and my effects working OK and I can create some mean effects using the Congo Dyn...
    Posted to The Congo Forum (and Congo jr, too!) (Forum) by cknapper on 03-11-2007
    Filed under: Congo, programming, LED
  • Re: pixeline 1044

    Hello again, I don't have any experience with the PixelLine, but I just had a quick look at the PixelLine 1044 manual and to me it looks like you can set them to RES 27ch, but then you will loose the effects since RES is only available in the DMX mode (not in Max1). And DMX mode doesn't have...
    Posted to The Congo Forum (and Congo jr, too!) (Forum) by okrogell on 03-10-2007
    Filed under: LED, Fade with Intensity
  • Pixel Line 1044 cells into groups

    Hi all, I'm using 8 Pixel Line 1044 on a outdoor event and have no time to plot really. So my question is I would like to run these so each battern has 6 cells. I then would like to have different groups to do different things during the concert. (e.g I want all the bottom cells in one group and...
    Posted to The Congo Forum (and Congo jr, too!) (Forum) by cknapper on 08-02-2009
    Filed under: LED, Groups
  • LED fixture library

    I've noticed that the LED fixture profiles include parameters for Brightness and Intensity. What's the difference? I'm asking because of the behavior of the Color Blaze 72s that were just installed in the theatre here. It may be that Saturation is actually the problem, but we haven't...
    Posted to The Eos (and Ion) Forum (Forum) by ctrl7 on 09-14-2009
    Filed under: HSB, Fixture library, LED
Page 1 of 4 (39 items) 1 2 3 4 Next >
Powered by Community Server (Commercial Edition), by Telligent Systems