The Eos (and Ion) Forum

Re: RFR and v 2.0 update

nfarwell — Wed, 05 Aug 2009 23:20:17 GMT

Question about the RFR - is it just me or did I used to be able to hit "channel 25 at enter" in live mode and have it take the channel out? It doesn't seem to do that anymore. I know I can do "at 00" or "at out" but my muscle memory is pretty strong from spending 60% of my RFR time in Park so I can access addresses.

Re: RFR and v 2.0 update

nfarwell — Tue, 23 Jun 2009 17:07:27 GMT

USB connected. I went through the exciting and complicated process of upgrading my GCE, then upgrading the RFR, then testing yesterday. I will see if it reboots anymore today with 2.0.2 installed. Both still had the 2.0.11 installed by service. On a side note, can the RFR update notifications go out via the registered product email list?

Will the RFR update ever get easier? Like, standalone? Using GCE still seems clunky (and the phone support guys anonymously agree).

Re: RFR and v 2.0 update

Anne Valentino — Tue, 23 Jun 2009 13:27:01 GMT

Can you please contact Matt Kerr in Tech Support??

Thanks much.... are you networking this RFR or is it connected via USB?

Re: RFR and v 2.0 update

nfarwell — Mon, 22 Jun 2009 17:07:46 GMT

One of my RFRs has started the rebooting again. Good thing the show closed yesterday!

Re: RFR and v 2.0 update

nfarwell — Mon, 27 Apr 2009 16:09:20 GMT

No additional functionality which outweighs the rebooting problem that I can find. Wait for the 2.0.11 update.

I had two very early RFR without the belt clips - so to get one of the newer ones is a nice bonus!

Re: RFR and v 2.0 update

Tim Wilson — Sun, 26 Apr 2009 02:10:22 GMT

I gave up on the temporary fix for the version 2 software. It never did seem to take a charge. Endless rebooting after a few minutes on.

So I reinstalled the original software and all is well. I haven't found the need to use the basestation on the network so far anyway.

Does the newest RFR software offer any additional functionality besides the ability to put the basestation on the network?

Re: RFR and v 2.0 update

Tim Wilson — Fri, 24 Apr 2009 17:01:34 GMT

Call tech support. I called yesterday and they explained the problem and sent me files for downgrading the RFR to original specs.

They also explained a procedure for allowing the RFR to get a full charge running the version 2 software which seems to be working.

I am going to try the next version of software which is supposed to address this issue before I restore to the original software.

Re: RFR and v 2.0 update

tdrga — Fri, 24 Apr 2009 14:32:54 GMT

Is there a hardware change? The belt clip on my RFR is screwed on, not a permanent attachment.

I am eagerly awaiting the new software to see if it fixes the rebooting problem, becuase I haven't been able to find downtime to send our RFR in for service.

-Todd

Re: RFR and v 2.0 update

dvarian — Thu, 23 Apr 2009 16:12:03 GMT

This software will be released in the next few days.

Dennis Varian

Re: RFR and v 2.0 update

nfarwell — Thu, 23 Apr 2009 16:01:15 GMT

Software version 2.0.11 seems to fix the battery/power/rebooting issue. I got back a surprise new RFR (with an integral belt clip! Thanks!) with the new software and then my other repaired one a few days later. So far, it works. Thanks guys.

Re: RFR and v 2.0 update

nfarwell — Wed, 15 Apr 2009 18:55:35 GMT

My RFR is now on it's way back to me and I will then play with the beta and give a report.

(note: when the customer is calling every day asking if it's done yet and telling you his only other RFR is not functioning while in tech rehearsals, shipping back the repaired RFR via GROUND is not conducive to low customer stress)

Re: RFR and v 2.0 update

nfarwell — Sat, 11 Apr 2009 20:22:36 GMT

I called ETC on Thursday to see the status of the one RFR in repair and they said it was in testing with a new version of the software. I really hope testing goes well as the one I'm using in tech right now has started rebooting randomly even while plugged into USB power. I really need a working remote - the one I still have is not wireless anymore and is not very functional.

Re: RFR and v 2.0 update

tdrga — Fri, 03 Apr 2009 21:57:45 GMT

bryankacz:

Second problem I've noticed is if I turn off the RFR when it's in park mode, some times when I turn it back on the display will read Live, but it will respond to commands as if it's in Park still, for example the Rem-Dim button will produce an error.

-Bryan

I have noticed this problem (RFR screen shows "live" but responds as if in "park") as well on our RFR v2.0 with networked base station.

I am also having the problem with the constant reboot at low battery level- same symptoms as nfarwell. For now I just use used batteries leftover from our wireless mics to keep the RFR running.

-Todd

Re: RFR and v 2.0 update

bryankacz — Fri, 03 Apr 2009 19:54:31 GMT

We had the same problem with ours when I upgraded to 2.0. Had to send it back to ETC, they sent us a replacement.

I'm having 2 issues with the replacement:

First, On the replacement the screen seems to be brighter in some parts than others. I would estimate that majority of the screen is running at 75% while the area where the battery indicator is and everything right below the battery are running at 100%.

I e-mailed ETC about this a week or so ago and haven't heard back.

Here's a very blurry picture that kind of shows the problem. It's much more noticeable in real life than the photo makes it look.

Second problem I've noticed is if I turn off the RFR when it's in park mode, some times when I turn it back on the display will read Live, but it will respond to commands as if it's in Park still, for example the Rem-Dim button will produce an error.

-Bryan

Re: RFR and v 2.0 update

corey — Fri, 03 Apr 2009 06:02:25 GMT

Hey Guys,

rebooting constantly sounds like a hardware problem. Could you please contact ETC Tech Services to see about having your Handheld sent in for repair.

For technical support in the Americas, please call 608/831-4116, or toll-free in the U.S. at 800/688-4116.
For technical support in Europe, please call (+44) 20 8896 1000.
For technical support in Germany, please call (+49) 8024 4700-0
For technical support in Asia, please call (+852) 2799 1220.